World's First All-in-one Air Purifier with Fragrance Dispenser

• Size: 262mm * 180mm * 52mm
• Net weight: 0.9 kg 
• Low voltage power supply: 0.16 kg 
• Package weight: 0.34kg
• Total weight with packaging:  1.4KG

• Equipped with 3 silent fans, with a noise level of 23.7dB.
• Maximum air volume: 0.4m ³/ Minute, purifying 24m per hour ³
• The air. Suggested elevator area ≤ 4 square meters, with an internal space of 12m ³.
• The purification time for M1 is 30 minutes.

• Electric parameters: 8W/hour of electricity consumption in continuous operation.
• LED light = 1.5 w/h.
• Negative ion module = 1.5w/h. Service life: every 10000 hours ( negative ion output decreases by 20%).
• Negative ion output quantity: In the working state of the negative ion module, the air discharged from the air outlet has a negative ion content of 30,000,000 units/cm ³/ second.
• Fan=5w/h, service life ≥ 30000 hours.
• Air quality sensor: 100 micrograms/m ³.
• When the concentration of suspended particles in the air exceeds this number, the red LED light flashes and the negative ion generator starts working. When the concentration of suspended solids in indoor air is below 100 ug/m ³, the air quality meets excellent standards and the red light automatically turns off.
• The motion sensor has three functions: detecting distance, indoor brightness, and running time.
• The maximum detection distance is 8 meters, and the distance set before the equipment leaves the factory is 4 meters.
• Indoor brightness: set the brightness at which the device enters standby mode, and set all-weather standby mode before leaving the factory.
• Running time: refers to the time when the device starts working after detecting human activity.

1. Attach the stainless steel mounting plate to the wall, determine the drilling position, then use a M4 diameter drill bit to drill holes, and then use the product's built-in drill tail screws to fix the mounting plate to the wall.

2. Remove the product and select the direction of the power cord outlet. Remove the adhesive strip from the outlet slot and place the power cord into the slot. To avoid air leakage from the back of the product, do not remove the adhesive strips from other cable trays.

3. Align the product with the hooks on the installation board, press firmly between the product and the installation board, and then move the product 1 centimeter downwards. The anti-theft buckle inside the product will automatically lock the hooks on the installation board.

4. Connect the power cord to the elevator power supply and secure the power cord.

5. After powering on, press the start button of the product, the blue LED light of the product will flash, and the device will enter the working state.

1. After the device is powered on, press the start button and the blue light bar will light up. At this point, the device enters standby mode.
2. In standby mode, the internal air sensor of the product automatically detects the indoor air quality. If the air quality is lower than the standard of good air, the red LED light will light up, and the product will automatically start working to purify the indoor air. When the indoor air quality is qualified, the red light will go out, and the equipment will enter standby mode.
3. When personnel enter the elevator, the motion sensors inside the product detect human activity, and the product automatically runs, creating a fragrance in the air. After 5 minutes of personnel leaving, the equipment automatically stops running and enters standby mode.
4. After entering the elevator, the air sensor detects the air quality. If the air quality is not good, the negative ion module of the product begins to work, emitting high concentrations of negative ions and ozone indoors (the emitted ozone concentration meets health standards, and the indoor ozone content is less than 0.05 PPM)
5. After product installation, it is recommended to power on 24/7 to ensure that the product is in standby mode. When the product is in standby mode, the power consumption is very low, averaging 2W/hour. It can ensure that the internal air is clean and excellent.

• The fragrance tube is located on the side of the product button switch.
• When replacing the fragrance tube core, press inward and quickly move your finger away.
• The fragrance tube will automatically pop out 8mm.
• Take out the fragrance tube and rotate the sealing cap.
• Replace the new fragrance tube core with the old one, tighten the sealing cap, and then insert the fragrance tube.